1 Standard exported package: Internal anticollision protection, external export wooden box packaging.
2 Shipping by express, by air, by sea according to customers' requirements to find the most suitable way.
1 - 1
To be negotiated
Small vacuum split induction heating melting system with with 80 mm quartz tube
CY-25VIM is a small vacuum split induction heating/melting system with complete accessories, including a 15KW induction heating power supply, Quartz Tube with Flange & Valve, Graphite Crucible & Refractory Assembling, 4L/m Recirculating Water Chiller, Vacuum Pump, and Mobile Cart. It is an ideal tool for researching new metallic alloys with both melting points < 2000ºC and quantity < 500g.
Working Voltage: 220V AC, 50/ 60 Hz, Three Phase
Working Current: 42 Amp (50A breaker required)
Max. Input Power: 15KW
Output Frequency: 30 - 80 kHz Adjustable
Duty Cycle: 80%
Induction Coil: 95mm(OD) x 85mm(ID) x 50mm(H)
Auto Heating Time: 1-99 seconds
Auto Dwell Time: 1-99 seconds
Auto Cooling Time: 1-99 seconds
Air Cooling: Rear Fan
Protection: Automatic water pressure, over-temperature, and overpower protection
Vacuum Chamber & Graphite Crucible
Half Open Quartz Tube is included with dimensions of 80mm(OD) x 75mm(ID) x 300mm(L)
Optional: 100mm(OD) x 92mm(ID) x 300mm(L) Quartz Tube is available at extra cost
Stainless Steel Flange with high-temperature silicone o-ring and self-tighten structure
Two valves and vacuum gauge installed on the flange.
KF25 connector and 1000mm long SS pipe is included for connecting to the vacuum pump
Complete refractory assembling made of alumina, including bottom crucible support, crucible holder, and cover.
One chamber shield is included to protect the chamber from foreign objects damage as well as containing the exploded piece of the chamber.
This induction heating system can reach 2000oC via graphite heater
No temperature controller. The temperature will be determined by sample melting via adjusting current
If you need accurate temperature control, please order the induction heating system at CYKY
Temperature range: 5 - 30°C
Water Flow Rate: 16 L/min
Water Tank: 12 Liters made of stainless steel
Note: It is recommended to use the specific coolant to get the best performance.
For US customer, 110V water chiller will be included
One 156L/m Rotary Vane Vacuum Pump is included
Rate: 156 L/min
Max. Power Consumption: 0.4KW / 0.37KW
For US customer, 110V Vacuum pump will be included
Heavy Duty Mobile Cart
Structure: Steel Frame Mobile Cart
600mm(L) x 800mm(W) surface for placing Induction Heater & Quartz Tube with Flange
For Non-UL Certified version, a protective shield made of phenolic sheets will be provided.
For UL Certified version, a clear protective shield made of polycarbonate will be provided.
The protective shield is to be placed around the quartz tube to contain the shooting glass shards if accidents were to happen.
Induction Heater: 18.5"(L) x 12"(W) x 17"(H) (470mm x 300mm x 430mm)
Water Chiller: 18"(L) x 8.7"(W) x 28"(H) (460mm x 220mm x 530mm)
Heavy Duty Mobile Cart: 600mm(L) x 800mm(W) x 597mm(H)
One year limited warranty with lifetime support
Consumable parts such as processing tubes, o-rings, and heating coil are not covered by the warranty
The heater will shut down if over output occurs. Please reduce coil cycle number or sample size to keep the heater operating under Max power
Melting time and temperature are related to materials, the crucible, refractory insulation, etc. If you do not know whether the induction heater can melt your sample or not, please contact our engineer for consulting. Have your alloy's composition, melting point, and quantity to be melted prepared
The Induction Melting System is designed for use under vacuum and low pressure < 0.02 MPa / 0.2 Bar/ 3 PSI and the flow rate for gases should be limited to < 200 SCCM ( or 200ml/min
Attention: A pressure regulator must be installed on your input gas tank and have the output gas pressure set below 3 PSI at all times after opening the gas tank with the gas maintained in a continuous flowing condition. Gas build-up with pressure levels exceeding over 3 PSI may cause irreversible damage to the furnace chamber.
Never heat the furnace while the gas release valve is closed and a positive pressure condition exists within the furnace chamber. The pressure gauge must be used to closely monitor the chamber condition at all times during the heating process; please open the gas release valve immediately once the chamber pressure has reached over 3 PSI to prevent unforeseeable damages.
105 kg (230 lbs)
160 kg (350 lbs)
47" x 40" x 40"
Founded in 2005, Zhengzhou CY Scientific Instrument Co., Ltd. is a company specializing in the development and production of laboratory technology research equipment. The products are mixed, pressed, burned, cut, ground, polished, coated, analytical equipment and related consumables. Products include laboratory sintering equipment, coating equipment and so on. At present, it has been exported to 25 countries and regions such as the United States, Europe, and Southeast Asia, and has been well received by various scientific research units.
We have a mature technology research and development team, the number of technicians is 33, the company has 150 people, more than 500 square meters of office space, the factory covers an area of about 1,500 square meters located in Zhengzhou High-tech Zone Electronic Industrial Park. The products are mainly located in the research market, serving scientific research in the labs of universities and colleges, and can also customize products according to your needs.
Q. Are you a manufacturer or a trading company?
A. We are professional laboratory instrument manufacturers, have their own design team and factory, have mature technical experience, and can guarantee the quality of products and the optimal price.
Q. How is your company's product after-sales service system?
A. The product warranty period is 12 months, we can provide lifetime maintenance. We have professional pre-sales and after-sales departments that can respond to you within 24 hours to resolve any technical issues.
Q. How long is your delivery time? If I want to customize the instrument, how long does it take?
A.1. If the goods are in stock, it is 5-10 days. 2. We can provide customized services for our customers. It usually takes 30-60 days depending on the specifications of the custom instrument.
Q. Our country's power supply and plug are different. How do you solve it?
A. We can supply a transformer and plug according to your local requirements according to the power plug of different countries.
Q. How to pay?
A.T / T, L / C, D / P, etc., it is recommended to use Alibaba Trade Guarantee.
Q. How is the package of goods? Delivery methods?
A.1. Standard export fumigation sign wooden box packaging 2. Express, air, sea shipping according to customer requirements, find the most suitable way.